Effect of scanning speeds on electrochemical corrosion resistance of laser cladding TC4 alloy

doi:10.1088/1674-1056/28/2/026802

Abstract In order to study the effect of scanning speed on the electrochemical corrosion resistance of laser cladding TC4 alloy in artificial seawater, the x-ray diffraction analysis, microstructure of cross-section, microhardness variation, and impedance spectrum have been studied in comparison with the TC4 titanium alloy. The results show that the main phase of cladding coating is α-Ti, and the change of scanning speed has no obvious effect on it; therefore, the supersaturated α-Ti solid solution is formed, and the acicular α' martensite is obtained. As the scanning speed increases, the microstructure of cladding coating is orthogonal basket-weave, the crystal surface spacing decreases, and the average microhardness of laser cladding TC4 alloy slightly increases. When the scanning speed increases to 10 mm/s, the microhardness is about 14.71% higher than that of the substrate, and the electrochemical corrosion resistance of laser cladding TC4 alloy is also improved, which is about 2.48 times more than the substrate. Grain refinement has a great effect on enhancing the anti-electrochemical corrosion.

Keywords: laser cladding TC4 alloy grain refinement electrochemical corrosion

Received: 01 October 2018
Revised: 13 December 2018
Accepted manuscript online:

PACS:	68.35.bd	(Metals and alloys)
	82.45.Bb	(Corrosion and passivation)

Fund: Project supported by the National Natural Science Foundation of China (Grant Nos. 61475117 and 51471084), the National Key Research and Development Program of China (Grant No. 2017YFB1103604), and the Tianjin Municipal Special Program of Talents Development for Excellent Youth Scholars, China (Grant No. TJTZJHQNBJRC-2-15).

Corresponding Authors: Jianbo Lei, Hong Gu
E-mail: ljbtj@163.com;guhong1120@163.com

Cite this article:

Xiaotian Feng(冯晓甜), Jianbo Lei(雷剑波), Hong Gu(顾宏), Shengfeng Zhou(周圣丰) Effect of scanning speeds on electrochemical corrosion resistance of laser cladding TC4 alloy 2019 Chin. Phys. B 28 026802

[1]	Polmear I, StJohn D, Nie J F and Qian M 2017 Light Alloys, 5th edn. (Boston: Butterworth-Heinemann) pp. 369-460
[2]	Shoesmith D W, Noël J J and Annamalai V E 2016 Corrosion of Titanium and Its Alloys in: Reference Module in Materials Science and Materials Engineering (Elsevier)
[3]	Cao S, Zhu S M, Samuel Lim C V, Zhou X G, Chen X B, Hinton B R W, Boyer R R, Williams J C and Wu X H 2017 Corrs. Sci. 125 29
[4]	Li C G, Wang B, Pan B, Huang W H and Wang Y 2015 Hot Work. Technol. 44 22 (in Chinese)
[5]	Sibileva S V, Botanogov A L, Trofimov N V and Zaharova L V 2015 Adv. Mater. Res. 1101 4
[6]	Critchlow G W, Brewis D M 1995 Int. J. Adhes Adhes 15 161
[7]	Mertens T, Gammel F J, Kolb M, Rohr O, Kotte L, Tschoecke S, Kaskel S and Krupp U 2012 Int. J. Adhes Adhes 34 46
[8]	Rico-Oller B, Mertens T, Kolb M, Wehr J and Zheludkevich M L 2016 Mater. Sci. Eng. Technol. 47 400
[9]	Yuan Q L, Feng X D, Cao J J and Su Z J 2010 Mater. Rev. 24 112 (in Chinese)
[10]	Chikarakara E, Naher S and Brabazon D 2012 Surf. Coat. Technol. 206 3223
[11]	Dong C S, Gu Y, Zhong M L, Ma M X, Huang T and Liu W J 2012 Acta Phys. Sin. 61 094211 (in Chinese)
[12]	Zhang K M, Zou J X, Li J, Yu Z S and Wang H P 2012 T. Nonferr. Met. Soc. 22 1817
[13]	Yan X J, Gugel H, Huth S and Theisen W 2011 Mater. Lett. 65 2934
[14]	Lei J B, Shi C, Zhou S F, Gu Z J and Zhang L C 2018 Surf. Coat. Technol. 334 274
[15]	Zhao Z, Chen J, Tan H, Lin X and Huang W D 2017 Opt. Laser Technol. 92 36
[16]	Weng F, Yu H J, Chen C Z, Liu J L, Zhao L J and Dai J J 2016 J. Alloys Compd. 686 74
[17]	Weng F, Yu H J, Chen C Z and Dai J J 2015 Mater. Design 80 174
[18]	Majumdar J D 2011 Adv. Mater. Sci. Eng. 2011 2237
[19]	Wang S L, Zhang Z Y, Gong Y B and Nie G M 2017 J. Alloys Compd. 728 1116
[20]	Gong F B, Shen J, Gao R H, Zhang T, Xie X and Yang L 2016 T. Nonferr. Met. Soc. 26 2117
[21]	Chen J M, Guo C and Zhou J S 2012 T. Nonferr. Met. Soc. 22 2171
[22]	Zhou S F and Zeng X Y 2010 J. Alloys Compd. 505 685
[23]	Wang X Y, Zhou S F, Dai X Q, Lei J B, Guo J B, Gu Z J and Wang T 2017 Int. J. Refract. Met. Hard Mater. 64 234
[24]	Ma Q S, Li Y J, Wang J and Liu K 2015 J. Alloys Compd. 645 151
[25]	Li G J, Li J and Luo X 2014 Mater. Charact. 98 83
[26]	Lu X L, Liu X B, Yu P C, Qiao S J, Zhai Y J, Wang M D, Chen Y and Xu D 2016 Opt. Laser Technol. 78 87
[27]	Weng F, Yu H J, Chen C Z, Liu J L and Zhao L J 2015 J. Alloys Compd. 650 178
[28]	Amado J M, Montero J, Tobar M J and Yáñez A 2014 Phys. Procedia 56 269
[29]	Chen J, Zhang S Y, Xue L, Yang H O, Lin X and Huang W D 2007 Rare Met. Mater. Eng. 36 475 (in Chinese)
[30]	Sun Y W and Hao M Z 2012 Opt. Laser Eng. 50 985
[31]	Wen R J, Tan H, Zhang F Y, Chen J and Huang W D 2012 Appl. Laser 32 91 (in Chinese)
[32]	Weng F, Chen C Z and Yu H J 2014 Mater. Des. 58 412
[33]	Li G R, Wang F F, Wang H M, Zheng R, Xue F and Cheng J F 2017 Chin. Phys. B 26 046201
[34]	Chen J, Yang H O, Yang J and Huang W D 2004 Mater. Chin. 23 33 (in Chinese)
[35]	Lin X, Xue L and Chen J 2009 Chin. Surf. Eng. 22 19
[36]	Zhang S Y, Lin X , Chen J, Zhang F Y and Huang W D 2007 Rare Met. Mater. Eng. 36 1839
[37]	Li Y S, Wu X C, Liu W, Hou Z Y and Mei H J 2015 Chin. Phys. B 24 126401
[38]	Picasso M, Marsden C F, Wagniere J D, Frenk A and Rappaz M 1994 Metall. Mater. Trans. B 25 281
[39]	Zhang S 2015 “Fabrication and Numerical Simulation of Cobalt-based Composite Coating on Titanium Alloy Surface by Laser Caldding”, MS dissertation (Dalian: Dalian University of Technology of China) (in Chinese)
[40]	Xu H Y, Zhang W, Fan K and Fu P F 2017 Rare Met. Mater. Eng. 46 1457
[41]	Chen J and Zhang Q 2016 T. Nonferr. Met. Soc. 26 1011
[42]	Bolzan J A, Jauregui E A and Arvia A J 1963 Electrochim. Acta 8 589
[43]	Schmuckler J S 1981 J. Chem. Edu. 58 404
[44]	Sato N 2011 Green Corrosion Chemistry and Engineering, Sharma S K Ed. (Weinheim: Wiley-VCH) pp. 1-32
[45]	Hu P, Song R, Li X J, Deng J, Chen Z Y, Li Q W, Wang K S, Cao W C, Liu D X and Yu H L 2017 J. Alloys Compd. 708 367
[46]	Cao C N 2008 Corros Sci. Prot Technol. 3 165 (in Chinese)
[47]	Walker R 1993 Mater. Design 14 207
[48]	Sulima I, Kowalik R and Hyjek P 2016 J. Alloys Compd. 688 1195
[49]	Cheng J, Li F, Zhu S Y, Yu Y, Qiao Z H and Yang J 2017 Tribol. Int. 115 483
[50]	Lin C H and Duh J G 2009 Surf. Coat. Technol. 204 784
[51]	Liao C J, Yang J S, He Y H and Ming X Z 2015 J. Alloys Compd. 619 221

[1]	Numerical research on effect of overlap ratio on thermal-stress behaviors of the high-speed laser cladding coating Xiaoxi Qiao(乔小溪), Tongling Xia(夏同领), and Ping Chen(陈平). Chin. Phys. B, 2021, 30(1): 018104.
[2]	Fine-grained NdFeB magnets prepared by low temperature pre-sintering and subsequent hot pressing Ju Jin-Yun (剧锦云), Tang Xu (唐旭), Chen Ren-Jie (陈仁杰), Wang Jin-Zhi (汪金芝), Yin Wen-Zong (尹文宗), Lee Don (李东), Yan A-Ru (闫阿儒). Chin. Phys. B, 2015, 24(1): 017504.

No Suggested Reading articles found!

Viewed

Full text

Abstract

Cited

Metrics
Related Articles

Effect of scanning speeds on electrochemical corrosion resistance of laser cladding TC4 alloy

Cite this article:

Online attention